A guide to...

Wet central heating systems

What is a wet central heating system?

With a wet central heating system, a central heat source (usually a boiler) produces hot water which is distributed around the property, heating radiators and becoming available for use from hot taps and showers.

This is generally considered the most cost effective and efficient way to provide heat and hot water for a property and is the most common form of heating in UK homes today with over 90% having a central heating system.

Boilers

In most wet systems, a boiler heats the water that feeds the system. The boiler will most commonly use gas as a fuel to do this, but it is also common to see oil or LPG (Liquid Petroleum Gas) used as a fuel where mains gas is not available.

Combination boilers

Commonly known as ‘combi’ boilers for short, are the most popular type in the UK. They provide hot water on demand without the need for a header tank or cylinder, therefore saving space.

Standard boilers

These have a cylinder where the hot water is stored ready for use.

In most cases, heating water instantly is more energy-efficient than ‘stored’ hot water systems. It also ensures that you don’t run out of hot water and have to wait for it to be reheated. However, the flow of hot water may slow if lots of hot water taps are used at the same time.

Boiler efficiency

Most boilers of both types purchased today will be condensing boilers. These are more energy efficient because they capture some of the heat which would normally escape from the flue and re-use it.

Like many appliances today, boilers are rated for efficiency from A to G according to their efficiency:

A new A-rated gas, oil or LPG boiler will be more than 90% efficient*ii. This means that they will use at least 90% of the energy stored in the fuel to heat the water in the system.

Getting your boiler serviced each year will help to maintain its efficiency. This will also ensure that it is operating safely, avoiding the creation of dangerous gases such as carbon monoxide.

When you come to get your boiler serviced, ensure you use a Gas Safe engineer if you have a gas or LPG boiler or an OFTEC registered engineer for an oil boiler.

However, even a well-maintained boiler will become less efficient over the years and if your boiler is over 15 years old or is running at a very low efficiency (ask your heating engineer when they service your boiler) you may wish to consider replacing it with a condensing boiler. You can find the efficiency of most boilers at http://www.homeheatingguide.co.uk/efficiency-tables.html

Upgrading from a G-rated boiler to a modern A-rated boiler can save as much as £340 per year on your fuel bills

Controlling your wet central heating system

With the average UK household spending more than 50% of their annual fuel bill on heating and hot water, large savings can be made by making best use of the heating controls you have available.

Effective use of heating controls can also increase levels of comfort, helping to ensure that people stay warm and well.

Common heating controls

Most ‘wet ‘central heating systems will have one or more of the following controls:

1) Boiler thermostat

Most boilers have a dial, marked either with numbers or a scale from Min to Max. In most boilers, the boiler thermostat controls the temperature of water sent to both the hot water cylinder and the radiators.

With ‘combi’ boilers, the temperature for the heating and hot water can often be set separately.

2) Programmer or timer

Programmers or timers let you set when you want the heating to be on. It is more energy efficient to only have the heating on when the house is occupied. It is a myth that it uses less energy to leave the heating on constantly.

However, remember that it will take some time for the house to heat up and that it will retain the heat for some time after the heating is switched off. Therefore, factor in these warm up and cool down times when setting your timer.

Remember, you can also turn your heating off when you go away on holiday. If it is very cold, leave on a low temperature just to ensure that the pipes don’t freeze (unless your system has automatic frost protection).

If you have a standard boiler, it is likely that your programmer will control the hot water as well. You can sometimes set the hot water times separately. It is best to set the hot water to only be on for as long as required to produce the amount of hot water you need. Experiment with reducing the amount of time the hot water is on each day to find the minimum amount of time it can be on whilst still producing enough hot water for your needs.

Most programmers also have some form of over-ride allowing you to turn the heating (and hot water if applicable) on or off manually as required. This can be useful when your occupancy patterns change from the norm.

There are two main types of programmer:

Mechanical programmers

Usually have a set of sliders (called ‘tappets’) which you move around a clock face. You use these to set the times of day you’d like the boiler to switch on and off.

Digital programmers

Display information on a screen. You can often set different time patterns for different days of the week.

3) Room thermostat

A room thermostat allows you to set the desired temperature using either a dial or a digital display. The thermostat senses the temperature of the air around it and sends a signal to the boiler to switch off once the desired temperature is reached.

Set the temperature as low as possible whilst keeping the temperature in the main living areas comfortable. However, be aware that this should never be done at the expense of health. Public Health England recommends that main living areas are heated to at least 18°C. However, the very young, elderly and vulnerable may require a higher temperature.

4) Thermostatic Radiator Valve (TRV)

Allows you to control the temperature in different rooms. Set these fairly high in the main living areas and lower in bedrooms and rooms that are not used very often.

5) Hot water cylinder thermostat

Controls the temperature hot water is stored at. Set to 60°C. This is hot enough to kill of harmful bacteria whilst not using excessive energy.

What else can I do to improve my central heating system?

Insulate your hot water cylinder

Most modern cylinders are factory insulated which helps to keep the water at a higher temperature. However, some older cylinders are not well insulated and you can buy a hot water tank jacket to improve the insulation for around £15 from most DIY stores. This could cut heat loss from the cylinder by more than 75% and could save you around £25-£35 a year, which is more than the cost of the jacket.

Bleed radiators regularly

Air can become trapped in the heating system, preventing radiators from working effectively. This can easily be remedied by bleeding the radiators to allow the air to escape. For detailed instructions see www.uswitch.com/energy-saving/guides/how-to-bleed-a-radiator.

Energy saving tips

  • Only have the heating on when someone is home.
  • Work out your warm up and cool down times to help you set your timer effectively.
  • Have the hot water on for just long enough to produce the amount of hot water you need each day.
  • Turn your heating off when you go on holiday. If it is very cold, leave on a low temperature just to ensure that the pipes don’t freeze.
  • Check that the clock is set correctly and remember to adjust it when the clocks change (if it doesn’t do this automatically).
  • Try reducing the temperature your thermostat is set to. However, be aware that this should never be done at the expense of health.
  • If you are cold, try putting on a jumper before resorting to turning the heating up
  • Avoid opening external windows and doors whilst the heating is on as this lets valuable heat escape (however, some ventilation is required in order to avoid the build-up of condensation).
  • Make sure that heaters are not covered and have plenty of space around them to allow the heat to circulate effectively.
  • Avoid covering heaters or radiators with curtains.
  • Fit reflective foil behind your radiators to reflect heat back into the room.
  • Set Thermostatic Radiator Valves to a lower setting in rooms which are not used very often.
  • Set your hot water cylinder to 60°C which is hot enough to kill off any bacteria whilst not wasting valuable energy.
  • Insulate your home – It will warm up faster and retain the heat for longer, saving energy and money. See our separate leaflets on insulating your home.

More advice

Our advisers are on hand to answer any questions you may have, and may also be able to offer you a free home visit to provide in-depth advice specific to your property and needs. Give us a call on 0800 500 3076 for more information.